Just how to Install a Bathtub ( Guide).
Just how to Install a Bathtub ( Guide).
Blog Article
The content listed below relating to Installing A Bathtub is particularly enlightening. Read it for your own benefit and see what you think of it.
Setting up a bath tub isn't specifically rocket science, but it does need strong plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old tub with a brand-new one is additionally a moderately challenging job. If the old bathtub is conveniently accessible, the project can move immediately; if you need to open up a wall surface to remove the old tub as well as place the brand-new bath tub, the job is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also embeded in the new one. Make sure you have qualified on your own for the task and also fit trying it. As opposed to hiring a service provider to take over a halfway-completed project, it is better to consider employing one before you begin. Possibilities are you may need an expert plumber to make tube connections.
This short article will assist you set up a new tub in your restroom if you have already purchased a new tub and don't need to transform the plan of your previous water system pipes.
Your tools and also product checklist ought to comprise the following:
Planning for the Setup
First of all, the supporting structure supplied with the bath needs to be fitted (if needed) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is essential to make sure that if the faucet comes with a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets unit to stop strain on the tub.
Fit the adaptable tap ports to the bottom of both taps making use of 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you use all of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its final placement.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installation, then the first thing you must do is separate the supply of water. After doing so, switch on the faucets to drain pipes any water staying in the system. The procedure of getting rid of the existing taps can be quite troublesome as a result of the limited access that is frequently the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a towel ready for the remaining water that will come from the pipelines. When the supply pipelines have actually been gotten rid of, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from transforming throughout this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleaned of any old sealing compound.
Before proceeding to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Setting up the Tub
Utilizing both wooden boards under its feet, put the tub in the needed setting. The wooden boards are useful in evenly spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by checking the level and also readjusting the feet on the tub up until the spirit level reads degree.
To mount faucets, fit the bottom of the furthest flexible faucet adapter to the proper supply pipe by making a compression join; then do the very same for the various other tap.
Switch on the water supply and also examine all joints as well as new pipework for leaks as well as tighten them if required. Fill the bathtub and also examine the overflow electrical outlet as well as the normal electrical outlet for leakages.
Finally, deal with the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bath tub must wait up until the bathtub has actually been utilized at least when as this will settle it right into its final position.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the faucet as well as the other end gives a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in area between the faucet as well as the sink. Secure the faucet in place with the maker provided backnut. As soon as the tap is safely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with regular tap adapters. The former kind ought to be attached to the tap finishes first, tightening just by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the area where the bathroom meets the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to break an inflexible seal, causing the water to permeate the wall surface between the bath and also the tiling, resulting in issues with dampness and feasible leakages to the ceiling below.
You can select from a selection of coloured sealants to blend in your components and also fittings. They are offered in tubes and also cartridges, and are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly load the bathtub with water before securing, to permit the movement experienced when the tub is in usage. The sealer can fracture fairly early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly readily available on the market. It is a good idea to fit the floor tiles making use of water-resistant or waterproof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you liked our section on Tools You Need to Install a New Bathtub . Thank you so much for taking the time to browse our content. Do you know another person who is excited about the subject? Take a moment to share it. I value reading our article about How to Install a Bathtub Yourself.
Book Today Report this page